Mount-It! Full Motion Articulating Heavy Duty Dual Monitor Desk Mount w/ USB 3.0 Ports Fit 17-35 in, 33 Lbs. Capacity Per Arm w/ Adjustable Gas Spring

This monitor does not support 2 27-inch monitors as advertised.

The fit for my two 32" curved monitors is a little tight, but it works. Sturdy construction. I ended up installing it in my desk vs. using the base, because I thought it may tip over, but smaller monitors may not have that issue.

Great product and once setup it is very easy to use. Looks good on the desk also. I got a little scared when one of the screws fell out of the bag, but I eventually found it in the box. My desk has a slight bezel which causes the mount to move a little when turning the main support arms. However, these arms do not need to be moved once in place, the gas shocks and swivel take care of the fine-tuning placement of the monitors. My only suggestion is that there are two screw clamps instead of one or a bracket that I can screw into my desk with 4 mounts instead of one giant screw. For reference, I have two 27" curved monitors.

was skeptical at first but once i put it together it was solid and well balance for holding two 27 inch monitors

I wish the last Section of arm behind the monitor was adjustable in length. The monitor comes out too far from the back of the desk. This is even after rotating the bottom outward. But it will work for me for now.

This monitor mount is much better than our old one. With our old one, you have to move the assembly up and down a pole and it tightens with an Allen wrench. This one adjusts in about any configuration you want. I bought this one for another employee because I like mine so much.

Good Quality mount and reasonable prices really no regrets.

impossible to have the tops of the monitors level, one always higher than the other. Had to rig a fix.

These monitor stands are terrific! Solidly built and easy to put together. We've outfitted our entire call center with them. I've only gone up to a 24" monitor, but with two that size it remains sturdy and balanced.

Excellent monitor mounts with simple, straightforward instructions. Only gripe I have is that the arms needed to be tightened quite a bit out of the box but that only took a few more minutes. Would recommend.

Awesome product help me clean up my desk and gave me more room would recommend

A really neat product! I’ve purchased the silver, model with clamp and have it affixed to a metal side table that’s barely 1/16”. It cleanly hides monitor cords and was pretty straightforward to put together. It’s also very sturdy. The only down side is that I thought the arms would have been a bit less chunky. However I see the girth is necessary to store the cords. It does what it’s supposed to so I’ll zip my lip and enjoy it.

I bought 3 of these stand and they are good stands at a good price. I will buy more when i need to.

Bought the MI-2781 stand for dual 24 inch monitors. The vesa mount wobbles on the arm and this makes adjusting the monitor difficult. The bracket on the back of vesa mount that slides over the mounting arm is to wide allowing the monitor to wobble. Other than that the stand was easy to assemble.

I bought my MI-2781 a month ago, love it and recommend it to my fellow engineers working from home. It is a great product for the price. I was concerned the weight of my two 24" DELL monitors would make the free standing V base front heavy and front tipsy. This has not been an issue. The moment arm distance from the center of the vertical post to the front fulcrum line of the V base is about 8" and the center of mass of my 2 monitors is about 5.5". See my attached diagram. It would be helpful if the Mount-It website would include the 8" forward moment arm length in their diagram. I did have an issue with the MI-2781A Installation Manual which I suspect is common for most Dell monitors. Step 5 of cannot be performed after step 4 because the VESA mount on the back of my Dell monitors is recessed about a quarter inch. In other words, it uses a carpenter's mortise and tenon joint. This is common to most of the Dell monitors I have used. After the VESA compatible plate is attached to the monitor per step 4, there is simply not enough clearance to perform step 5. Instead, I had to do the following. - undue step 4 (remove the plate from the back of my monitor), - perform step 5 (attach the 2 plates to the arms), - new step (lay both monitors face down on the floor), - perform step 4 (attach the VESA compatible plates to the back of the two monitors), - new step (lift and set the entire V-base assembly on my desk), - then continue with installation step 6.

Quality Mount at a reasonable price point. Easy to install and adjust. No problems with the arms holding up the monitors once they were adjusted correctly per the instructions. I used the grommet mount, as my desk did not have big enough edge to use the clamp. I figured this would be the case when I ordered it. That is one reason I picked this because of the multiple mounting methods.

I have two 34\ curved monitors. They fit great. The pump arms are so cool. I can easily twist

I had 1 mounted monitor and two on stands, but limited desk space. This was an excellent solution. Very happy!

Exactly what I needed, very good quality build parts, it let's you adjust the screens with many angle approaches, it even has a height adjustment for every screen mount so if your screens have a height difference due to a bigger frame or mount point you can adjust them all still to be the same height ( gives you an inch +/- of margin to play with) - not that common on these products.Note that if you plan not to attach the center pole to the table and simply place it as is with the base plate, you will limit yourself to the angle of how much you can turn the side monitors curved to your direction since the center-weight-point will be moved further then the base playe and it will fall forward. In my pictures you can see the maximum angle to curve without mounting the pole to the table.

These are very effective and a good value. Easy to assemble and came with a good selection of alternate mountings and screws for a variety of monitors and their backings. Took away one star because the joints were seriously hard to tighten or loosen in some spots. That said, once I was able to position in a way I liked, they look and work great.