E6000 2 Fl oz Multi purpose Craft Glue: Clear Adhesive for Wood, Glass, Metal, Rubber & Plastic, Dries Clear
About this item
Highlights
- This thick, permanently bonding adhesive is tough yet flexible
- Perfect for projects including glass, clay, beads, fabric, ceramics, wood, and metal
- Non-flammable once cured
- This clear adhesive is paintable - paint to match the surrounding area to make it UV-resistant
- Temperature resistant - unaffected by extreme heat or cold once cured
Description
Shipping details
Return details
Q: Does this work on car vinyl upholstery or do I need the e6000 extra b/c of heat and cold?
A: E6000 Craft is a great choice for mending automobile seat vinyl. It will hold well and flex with the vinyl during use. Its temperature range once cured is -40--180 F, so it should perform well. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 11 days agoBrand expert
Q: Does this dry fast like Super Glue?
A: No, E6000 is a solvent based adhesive that cures via the solvent evaporating. This takes about 24 hours for a cure, but it can take up to 48 hours for a full cure. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 2 months agoBrand expert
Q: Will this work on resin or ceramic decor pieces for repairs? I have a few cracked items I want to fix.
A: E6000 is a great choice for repairing ceramic and resin items. E6000 is clear, waterproof, and has over 2,000 lbs./square inch of strength. For best results, first clean the surfaces with acetone or rubbing alcohol. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 6 months agoBrand expert
Q: Will this work for trophies?
A: E6000 will work great for this application! Apply the adhesive to both surfaces to be bonded and allow it to partially cure for approximately 2 minutes before mating the surfaces together. Allow repair to cure for 24 hours. Depending on the materials and temperature, maximum strength may not be reached for 48 to 72 hours. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 8 months agoBrand expert
Q: Is E6000 good for nylon to nylon fabric patch?
A: E6000 is a great choice for bonding nylon-to-nylon. It will hold the patch very well. For best results treat the product as a contact adhesive, meaning apply the product to both surfaces and allow 2-3 minutes for the product to get tacky before mating the two together and clamping/securing with weight for 24 hours. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 9 months agoBrand expert
Q: Will this hold the handle of my mug together? I would normally use epoxy but I've ran out and have some E6000. Thank you :)
A: E6000 bonds great to repair ceramic and other mug materials and should do a fine job repairing the handle. However, its upper temperature limit is 180 F, so very hot beverages may cause the adhesive to soften and loosen. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 11 months agoBrand expert
Q: What's the difference between E6000 multi purpose and E6000 clear
A: E6000 is offered in a few different sizes and packaging configurations. Any tube that has a tapered tip (like the 2.0 oz. craft product) is our Low Viscosity formula, which is thinner than our Medium Viscosity which comes in larger tubes (3.0 oz. and 3.7 oz.). E6000 "Multi-Purpose" is verbiage Target uses for our adhesive. The only difference between these items is their thickness--strength, set time, cure time, elongation/flexibility, etc. are all the same. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 11 months agoBrand expert
Q: Can It be used to add metal to fabrics?
A: E6000 will work great for adhering metal to fabric! Apply it directly to each surface to be bonded, allow to partially cure approximately 2-3 minutes before mating surfaces. Thank you for your support of Eclectic Products & Target!
submitted byTeam Eclectic - 11 months agoBrand expert
Q: Can I use it to attach seashell to a canvas?
A: E6000 is a great choice for bonding seashells to canvas. For best results, first clean the seashells and the canvas surface with rubbing alcohol or acetone to remove any contaminants or barriers for a quality adhesion. Apply the adhesive and clamp or secure the seashell in place for 24 hours. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 11 months agoBrand expert
Q: What is the working time. I need a quick set.
A: E6000's tack time is 4 minutes; a full cure is 24-48 hours. For best results treat the product as a contact adhesive, meaning apply the product to both surfaces and allow 2-3 minutes for the product to get tacky before mating the two together and clamping/securing with weight for 24 hours. Thank you for your support of Eclectic Products and Target!
submitted byTeam Eclectic - 1 year agoBrand expert